高分辨率线扫描Sensors Unlimited 2048L提供方形像素(10 x 10 μm)用于机器视觉或高像素(10 x 210 μm),以便于与光谱仪对齐。 这些摄像机通过提供灵活性的Base Camera Link®接口提供每秒100到>76,000的线速。
高分辨率线扫描Sensors Unlimited 2048L提供方形像素(10 x 10 μm)用于机器视觉或高像素(10 x 210 μm),以便于与光谱仪对齐。 这些摄像机通过提供灵活性的Base Camera Link®接口提供每秒100到>76,000的线速。2048提供光学相干断层扫描(OCT)或工业机器视觉所需的高分辨率、稳定性和可靠性。 在0.98至1.65 μm的短波红外(SWIR)波长范围内提供高均匀灵敏度。 对所有像素的同时采集提供了重要的医疗和工业机器视觉所需的卓越的可重复性和较长的工作寿命。
GL2048L | QE(量子效率)
OPTO-ELECTRONIC PERFORMANCE
Sensor format 1
2048 pixels with 2048 readout ADCs on 10 µm pitch
Optical aperature (pixel height)1
210 µm or 10 µm
Quantum efficency1
> 60% over 0.98 µm-1.65 µm; > 70% peak response @ 1.55 µm
Gain setting
Temporal noise (rms counts)1 2
High
Medium High
Medium Low
Low
Typical
Specification
Typical
Specification
Typical
Specification
Typical
Specification
3.1
< 3.4
2.2
< 2.8
1.9
< 2.3
1.7
< 1.9
Dynamic range1,2
> 1200:1
> 1450:1
> 1750:1
> 2100:1
Differential non-linearity1,2
+/- 1.1
< +/- 2.5%
+/- 1.5
< +/- 2.5%
+/- 1.5
< +/- 2.5%
+/- 1.5
< +/- 2.5%
Bad pixel specification
White, dark, noisy or pixels exceeding +/- 20 % of the mean value when illuminated at 50% of full well.
Number of bad pixels limited to a maximum of 1% of array total; on-board pixel replacement function
Exposure time1,3
5.5 µs to 10 ms, user programmed in pixel clock cycles or via the width of the ext. trigger
Trigger modes 3
Free run, single line per trigger (exposure set by camera), or variable exposure
External trigger 3
Via CC1 signal line in Camera Link cable
External variable ET
User set by the duration of trigger input signal (minimum exposure time pulse: 5.5 µs)
External trigger jitter
+/-2.5 clock cycles: nominally 63 ns variation
Pixel rate
2048L:157 Mpix/s with 2 x 12-bit words transferred on each Camera Link strobe clock at 80 MHz
Digital output format
12-bit base Camera Link®;
recommend NI PCIe-1433 or frame grabber with throughput of > 313 Mbytes/s to PC motherboard
(minimum of 4 bi-directional PCIe express lanes in PC)
Readout mode
Integrate-While-Read, differential double sampling
Corrections (preset OPR)
Factory calibrated gain, offset, and bad pixel replace.
1 Actual formats and performance governed by pixel size options (dark current may limit longest usable ET, especially at high gain);
2 Camera readout noise limited for low & medium gain settings; dark shot noise limited for high gain settings at longer exposure times
3 Modes are user selectable by command over Camera Link® serial lines
INTERFACES
Control: & Data
GL2048L: Single SDR 26-pin connector
Power Connector
CUI Inc. PJ-056, 1.0mm X 3.8mm power jack
Trigger: Input
Via Camera Link CC1 line
Status LED:
Green: Power on
Tested Framegrabbers
Nat. Instruments PCIe-1429, -1433, Matrox Solios eV-CL PCIe-X4
*
REGULATORY COMPLIANCE
CE:
Meets class A for emission, immunity & ESD standards, RoHS
FCC:
Meets requirements for Part 15, Subpart B, Class A, 2006
*
ENVIRONMENTAL & POWER
Operating Case Temperature
+10°C to +35°C
Storage Temperature
-10°C to 60°C
Humidity
Up to 95% and non-condensing
Power Requirements:
AC Adapter Supplied
DC Voltage
Typical Power
100–240 VAC, 47–63 Hz
+6 to 12 VDC (Maximum: 13.1 VDC)
3.6 W at 30°C case temp1
In-rush Current
1.25 A @ 12 VDC
*
MECHANICAL
Width x Height x Depth:
8.3 cm x 10.2 cm x 1.6 cm (excludes I/O connectors, and lens adapter)
3.25 in x 4 in x 0.64 in (excludes I/O connectors, and lens adapter)
Weight:
< 240 g or 8.6 oz (no lens or adapter)
Threaded Lens Mount
M42x1-6H (focus point ~6 mm from camera surface)
Optional Lens Mount Adapters
C-Mount adapter or adjustable distance F-Mount adapter (see ordering info)
Spectrometer Mount
4 tapped 8-32 holes in 2 inch square pattern,
2 tapped 8-32 holes in-line with image axis,
O-Ring light seal, 1.9 inch diameter, 1/16th thickness
Camera Tripod
Mount
2 tapped¼-20 holes, one on bottom, one on side wall.
*
ORDERING INFORMATION
Camera Model
Part number
Max. Line rate
Pitch
Pixels
FPA length
Aperture (height)
Classification
GL2048L-10A-ENC-STD-210
8000-0596
76,263 lps
10 μm
2048
20.48 mm
210 μm
EAR99
GL2048L-10A-ENC-STD-010
8000-0597
76,263 lps
10µm
2048
20.48 mm
10 µm
6A003.b.4.a
Included items in qty 1-4: Power supply, lens cap, ESD foam-lined shipping box, mini-CD with manual and SUI Image Analysis software for National Instruments IMAQ environment.
Order lens adapters separately for additional charge:
Part Numbers: Adjustable F-mount adapter: 8000-0171. C-mount adapter: 3800-0002
SUI’s linescan cameras, accessories, and associated technical data are subject to the controls of the Export Administration Regulations(EAR). Export, re-export or transfer of these items by any means to a foreign person or entity, whether in the United States or abroad, without appropriate Department of Commerce authorization, is prohibited and may result in substantial penalties.